Aire - Campus Virtual

AIR CONDITIONER (SPLIT TYPE) Owner s Manual Indoor Unit Model name: Concealed Duct Hh Static Pressure Type RAV-SM2242DT-E RAV-SM2802DT-E Owner s Manual Air conditioner (Split type) 1 English Manuel du propriétaire Climatiseur (Type split) 23 Français Bedienungsanleitung Klimagerät (Split-typ) 45 Deutsch Manuale del proprietario Condizionatore d aria (Tipo split) 67 Italiano Manual del propietario Aire acondicionado (Tipo split) 89 Español Manual do proprietário Ar condicionado (Tipo split) 111 Português Gebruiksaanwijzing Airconditioner (Gesplitst type) 133 Nederlands ( Split) 155 (-) 177 Kullanım Kılavuzu Klima (Split tip) 199 Türkçe Concealed Duct Hh Static Pressure Owner s Manual Orinal instruction ADOPTION OF NEW REFRERANT This Air Conditioner uses R410A an environmentally friendly refrerant This appliance is not intended for use by person (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Contents 1 PRECAUTIONS FOR SAFETY 4 2 PART NAMES 7 3 WIRED REMOTE CONTROLLER 8 4 CORRECT USAGE 11 5 TIMER OPERATION 13 6 POWER SAVING MODE 14 7 ADVANCED SETTINGS 15 8 ENERGY SAVING RECOMMENDATIONS 16 9 MAINTENANCE AIR CONDITIONER OPERATIONS AND PERFORMANCE INSTALLATION TROUBLESHOOTING SPECIFICATIONS 22 1-EN 1 Concealed Duct Hh Static Pressure Owner s Manual Thank you for purchasing this Toshiba air conditioner Please read carefully through these instructions that contain important information which complies with the Machinery Directive (Directive 2006/42/EC), and ensure that you understand them Some of the details provided in these instructions differ from the Owner s Manual supplied with your product, and the instructions provided here take precedence After reading these instructions, be sure to keep them in a safe place together with the Owner s Manual and Installation Manual supplied with your product Generic Denomination: Air Conditioner Definition of Qualified Installer or Qualified Service Person The air conditioner must be installed, maintained, repaired and removed by a qualified installer or qualified service person When any of these jobs is to be done, ask a qualified installer or qualified service person to do them for you A qualified installer or qualified service person is an agent who has the qualifications and knowledge described in the table below Agent Qualified installer Qualified service person Qualifications and knowledge which the agent must have The qualified installer is a person who installs, maintains, relocates and removes the air conditioners made by Toshiba Carrier Corporation He or she has been trained to install, maintain, relocate and remove the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such operations by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to these operations The qualified installer who is allowed to do the electrical work involved in installation, relocation and removal has the qualifications pertaining to this electrical work as stipulated by the local laws and regulations, and he or she is a person who has been trained in matters relating to electrical work on the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such matters by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to this work The qualified installer who is allowed to do the refrerant handling and piping work involved in installation, relocation and removal has the qualifications pertaining to this refrerant handling and piping work as stipulated by the local laws and regulations, and he or she is a person who has been trained in matters relating to refrerant handling and piping work on the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such matters by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to this work The qualified installer who is allowed to work at hehts has been trained in matters relating to working at hehts with the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such matters by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to this work The qualified service person is a person who installs, repairs, maintains, relocates and removes the air conditioners made by Toshiba Carrier Corporation He or she has been trained to install, repair, maintain, relocate and remove the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such operations by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to these operations The qualified service person who is allowed to do the electrical work involved in installation, repair, relocation and removal has the qualifications pertaining to this electrical work as stipulated by the local laws and regulations, and he or she is a person who has been trained in matters relating to electrical work on the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such matters by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to this work The qualified service person who is allowed to do the refrerant handling and piping work involved in installation, repair, relocation and removal has the qualifications pertaining to this refrerant handling and piping work as stipulated by the local laws and regulations, and he or she is a person who has been trained in matters relating to refrerant handling and piping work on the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such matters by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to this work The qualified service person who is allowed to work at hehts has been trained in matters relating to working at hehts with the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such matters by an individual or individuals who have been trained and is thus thorougy acquainted with the knowledge related to this work EN 2 2-EN Concealed Duct Hh Static Pressure Owner s Manual Warning Indications on the Air Conditioner Unit Warning indication Description WARNING ELECTRICAL SHOCK HAZARD Disconnect all remote electric power supplies before servicing WARNING ELECTRICAL SHOCK HAZARD Disconnect all remote electric power supplies before servicing WARNING Moving parts Do not operate unit with grille removed Stop the unit before the servicing WARNING Moving parts Do not operate unit with grille removed Stop the unit before the servicing CAUTION Hh temperature parts You mht get burned when removing this panel CAUTION Hh temperature parts You mht get burned when removing this panel CAUTION Do not touch the aluminum fins of the unit Doing so may result in injury CAUTION Do not touch the aluminum fins of the unit Doing so may result in injury CAUTION BURST HAZARD Open the service valves before the operation, otherwise there mht be the burst CAUTION BURST HAZARD Open the service valves before the operation, otherwise there mht be the burst 3-EN 3 Concealed Duct Hh Static Pressure Owner s Manual 1 PRECAUTIONS FOR SAFETY WARNING General Carefully read Owner s Manual before starting the air conditioner There are many important things to keep in mind for daily operation Transportation and storage When transporting the air conditioner, wear shoes with additional protective toe caps When transporting the air conditioner, do not take hold of the bands around the packing carton You may injure yourself if the bands should break When stacking the packing cartons for storage or transportation, heed the precautions written on the packing cartons Failure to heed the precautions may cause the stack to collapse Installation Only a qualified installer(*1) or qualified service person(*1) is allowed to carry out the electrical work of the air conditioner Under no circumstances must this work be done by an unqualified individual since failure to carry out the work properly may result in electric shocks and/or electrical leaks After the installation work has been completed, have the installer explain about the circuit breaker positions In the event that trouble has occurred in the air conditioner, set the circuit breaker to the OFF position, and contact a service person If you install the unit in a small room, take appropriate measures to prevent the refrerant from exceeding the limit concentration even if it leaks Consult the dealer from whom you purchased the air conditioner when you implement the measures Accumulation of hy concentrated refrerant may cause an oxygen deficiency accident Do not install the air conditioner in a location that may be subject to a risk of expire to a combustible gas If a combustible gas leaks and becomes concentrated around the unit, a fire may occur Operation Before opening the intake grille of the indoor unit or service panel of the outdoor unit, set the circuit breaker to the OFF position Failure to set the circuit breaker to the OFF position may result in electric shocks through contact with the interior parts Only a qualified installer(*1) or qualified service person(*1) is allowed to remove the intake grille of the indoor unit or service panel of the outdoor unit and do the work required Inside the air conditioner are hh-voltage areas and rotating parts Due to the danger of electric shocks or of your fingers or physical objects becoming trapped in the rotating parts, do not remove the intake grille of the indoor unit or service panel of the outdoor unit When work involving the removal of these parts is required, contact a qualified installer or a qualified service person Do not move or repair any unit by yourself Since there is hh voltage inside the unit, you may get electric shock when removing the cover and main unit Use of a stand more than 50 cm hh to clean the filter of the indoor unit or to carry out other such jobs constitutes working at hehts Due to the danger of falling off the stand and injuring yourself while working at hehts, this kind of work should not be done by unqualified individuals When this kind of work must be carried out, do not do it yourself but ask a qualified installer or a qualified service person to do it for you Do not touch the aluminum fin of the outdoor unit You may injure yourself if you do so If the fin must be touched, do not touch it yourself but contact a qualified installer or a qualified service person Do not climb onto or place objects on top of the outdoor unit You may fall or the objects may fall off of the outdoor unit and result in injury Do not place any combustion appliance in a place where it is directly exposed to the wind of air conditioner, otherwise it may cause imperfect combustion When the air conditioner is operated with a combustion appliance in the same place, be careful of ventilation to let fresh air enter the room Poor ventilation causes oxygen shortage When the air conditioner is used in a closed room, be careful of sufficient ventilation of the room Poor ventilation causes oxygen shortage Repairs When you have noticed that some kind of trouble (such as when an error display has appeared, there is a smell of burning, abnormal sounds are heard, the air conditioner fails to cool or heat or water is leaking) has occurred in the air conditioner, do not touch the air conditioner yourself but set the circuit breaker to the OFF position, and contact a qualified service person Take steps to ensure that the power will not be turned on (by marking out of service near the circuit breaker, for instance) until qualified service person arrives Continuing to use the air conditioner in the trouble status may cause mechanical problems to escalate or result in electric shocks, etc If you have discovered that the fan grille is damaged, do not approach the outdoor unit but set the circuit breaker to the OFF position, and contact a qualified service person to have the repairs done Do not set the circuit breaker to the ON position until the repairs are completed If you have discovered that there is a danger of the indoor unit s falling, do not approach the indoor unit but set the circuit breaker to the OFF position, and contact a qualified installer or a qualified service person to refit the unit Do not set the circuit breaker to the ON position until the unit has been refitted If you have discovered that there is a danger of the outdoor unit s toppling over, do not approach the outdoor unit but set the circuit breaker to the OFF position, and contact a qualified installer or a qualified service person to have the improvements or refitting done Do not set the circuit breaker to the ON position until the improvements or refitting is completed 4 EN 4-EN Concealed Duct Hh Static Pressure Owner s Manual Relocation When the air conditioner is to be relocated, do not relocate it yourself but contact a qualified installer or a qualified service person Failure to relocate the air conditioner properly may result in electric shocks and/or a fire (*1) Refer to the Definition of Qualified Installer or Qualified Service Person CAUTION TO DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY This appliance must be connected to the mains by means of a switch with a contact separation of at least 3 mm The installation fuse 25A must be used for the power supply line of this air conditioner CAUTIONS ABOUT INSTALLATION (Be sure to confirm the following cautions) Certainly lay the drain hose for perfect draining Bad drainage may cause flooding in the house and getting furniture wet Make sure to connect the air conditioner to an exclusive power supply of the rated voltage, otherwise the unit may break down or cause a fire CAUTIONS ABOUT OPERATION Do not use this air conditioner for special purpose such as preserving food, precision instruments, art objects, breeding animals, car, vessel, etc Do not touch any switches with wet finger, otherwise you may get an electric shock If the air conditioner will not be used for a considerably long time, turn off the main switch or the circuit breaker, for safety To make the air conditioner operate in its orinal performance, operate it within the range of the operating temperature specified in the instructions Otherwise it may cause a malfunction, or water leak from the unit Prevent any liquid from falling into the remote controller Do not spill juice, water or any kind of liquid 5-EN 5 Concealed Duct Hh Static Pressure Owner s Manual Information on the Transportation, Handling and Storage of the Carton Examples of indication on the carton Symbol Description Symbol Description Keep dry Do not drop Fragile Do not lay down 11 cartons Stacking heht (12 cartons can be stacked in this case) Do not walk on this carton EN This side up Do not step Handle with care Other cautions Description CAUTION Injury possibility Don t handle with packing band, or may get injured in case of broken band Stacking notice In case that cardboard boxes protrude out of pallet when stacking Lay a 10 mm thick plywood over the pallet 6 6-EN Concealed Duct Hh Static Pressure Owner s Manual 2 PART NAMES Indoor unit Air discharge Connect a discharge duct Air intake Connect a suction duct Electrical control box The earth screw is provided in the electrical control box Separate sold part Remote controller Drain pan TIMER SET FAN MODE TIME SAVE VENT FILTER RESET TEST SET CL SWING/FIX UNIT LOUVER Outdoor unit Air intake (Side and rear) Front panel There is an earth screw, valves, and electric parts inside Air discharge Pipe cover Mounting leg Wire connection holes Refrerant pipe connection holes 7-EN 7 Concealed Duct Hh Static Pressure Owner s Manual 3 WIRED REMOTE CONTROLLER This remote controller can control the operation of up to 8 indoor units Display section In the display illustration below all the icons are shown When the unit is in operation, only relevant icons will be displayed When turning on the leak breaker at the first time, flashes on the display part of the remote controller While this icon is flashing, the model is being automatiy confirmed Wait till icon has disappeared to use the remote controller TEMP TIMER SET TIME FAN SAVE ON / OFF MODE VENT Display section Operation section FILTER RESET TEST SET CL SWING/FIX UNIT LOUVER EN 1 Operation mode The selected operation mode is displayed 2 Error display Displayed while the protective device works or a error occurs 3 SETTING display Displayed during setup of the timer or other settings 4 TEST run display Displayed during a test run 5 Timer display When an error occurs, error code is displayed 6 Timer mode display The selected timer mode is displayed 7 Filter display Reminder to clean the air filter 8 Fan speed display Fan speed is not adjustable It is fixed to Hh (HH) 9 Set temperature display The selected set temperature is displayed 10 Power saving mode display Limits compressor speed (capacity) to save energy 8 8-EN Concealed Duct Hh Static Pressure Owner s Manual UNIT No display Displays the number of the indoor unit selected Also displays error code of indoor and outdoor units 12 Central control display Displayed when the air conditioner is used under the central control in combination with a central control remote controller In case the remote controller is disabled by the central control system, flashes The button operation is not accepted Even when you push ON/OFF, MODE, or TEMP button, and the button operation is not accepted (Settings made by the remote controller vary with the central control mode For details, refer to the Owner s Manual of the central control remote controller) 13 Remote controller sensor display Displayed while the sensor of the remote controller is used 14 Pre-heat display Displayed when the heating mode is energized or defrost cycle is initiated While this icon is displayed, the indoor fan stops 15 No function display Displayed when the function requested is not available on that model 9-EN 9 Concealed Duct Hh Static Pressure Owner s Manual Operation section Push each button to select a desired operation The control saves commands in memory and after the initial setting, there is no need for any additional settings unless changes are desired The air conditioner can be operated by pushing the button button (Temperature set button) Adjusts the set point Select the desired set point by pushing TEMP or TEMP 2 button (Timer set button) Use to setup the timer 3 button (Filter reset button) Resets icon after cleaning filter 4 button (Test button) Use only for service (During normal operation, do not use this button) 5 button When the button is pushed, the operation starts, and it stops by pushing the button again When the operation has stopped, the operation lamp and all the displays disappear 6 Operation lamp Green lht illuminates when unit is on Although it flashes when operating the protection device or an error occurs 7 button (Operation mode button) Selects desired operation mode 8 button (Fan speed button) Fan speed is not adjustable It is fixed to Hh 9 button (Ventilation button) Use when a power ventilation kit (loy procured) is connected If is displayed on the remote controller when this button is pushed no vent kit connected 10 button (Power save operation) Use to initiate power saving mode 11 button (Unit/Louver select button) Selects a unit number (left) and louver number (rht) UNIT: Selects an indoor unit when multiple indoor units are controlled with one remote controller LOUVER: No Function 12 button (Swing/Louver direction button) No Function OPTION : Remote controller sensor Usually the temperature sensor of the indoor unit senses the temperature The temperature on the surrounding of the remote controller can also be sensed For details, contact the dealer from which you have purchased the air conditioner EN EN Concealed Duct Hh Static Pressure Owner s Manual 4 CORRECT USAGE When you use the air conditioner for the first time or when you change the setting, follow the steps below Settings are saved in memory and are displayed anytime the unit is turned on by pushing the button Preparation Turn on the main power switch and/or the leakage breaker When the power supply is turned on, a partition line is displayed on the display part of the remote controller After the power supply is turned on, the remote controller does not accept an operation for approx 1 minute, but it is not a failure REQUIREMENT While using the air conditioner, operate it only with button without turning off the main power switch and the leakage breaker When you re-power the air conditioner after it has not been used for a long period, turn on the leakage breaker at least 12 hours before starting the air conditioner (This is required to turn on the compressor case heater for warming in order to prevent overload on the compressor when activating the outdoor unit) Stop Push button The operation lamp goes off, and the operation stops 3 TEMP FILTER RESET TEST TIMER SET SET TIME CL Start 1 Push button The operation lamp illuminates, and the operation starts 2 Select an operation mode with the button One push of the button, and the display changes in the order shown below 3 Select a desired set point by pushing the TEMP or TEMP button FAN SAVE SWING/FIX ON / OFF MODE VENT UNIT LOUVER Auto Heat Cool Fan 1 2 NOTE Auto Changeover When in Auto Mode, the unit selects the operating mode (cooling, heating or fan only) based on the user selected set point temperature If the Auto mode is uncomfortable, you can select the desired conditions manually Cooling If there is a demand for cooling, unit will start approximately 1 minute after mode is selected Heating If there is a demand for heating, unit will start approximately 3 to 5 minutes after the mode is selected After the heating operation has stopped, fan may continue to run for approx 30 seconds When the room temperature reaches the set temperature, the outdoor unit stops and the indoor unit will carry on fan operation During defrost operation, the fan stops so that cool air is not discharged ( Pre-heat is displayed) When restarting the operation after stop When attempting to restart the unit immediately after it was stopped, the unit can not start for approx 3 minutes this is to protect the compressor 11-EN 11 Concealed Duct Hh Static Pressure Owner s Manual 8 C OPERATION (For object pre-heating) (Available for Super Dital Inverter outdoor units) The air conditioner can control the heating temperature to about 8 C in the heating mode The 8 C heating operation requires settings with the wired remote controller Ask the installer or dealer for the settings according to the installation manual of the indoor unit Start 1 2 Stop 1 Set the displayed temperature to 18 C in the heating mode by pushing TEMP Set the displayed temperature to 8 C by pushing TEMP Set the displayed temperature to 18 C by pushing TEMP button button for at least four seconds button The air conditioner returns to the normal HEAT mode Select a desired temperature and operation mode NOTE The discharged air temperature is lower than that in the normal heating operation The room temperature may not be heated evenly depending on the remote controller installation location The room temperature may not reach 8 C depending on the room size or the installation conditions The 8 C heating operation is cancelled in the following cases When operation is stopped with button When another operation mode is selected with button When temperature setting or operation mode is changed or operation is started/stopped by the wireless remote controller or the central control remote controller If one or more models other than the 4-way air discharge cassette type (4 series), slim duct, Concealed Duct Hh Static Pressure are connected in the same control , the 8 C heating operation is not available When you use this operation mode, observe proper operating hours and we recommend that you ask service staff for periodic maintenance of the air conditioner EN EN Concealed Duct Hh Static Pressure Owner s Manual 5 TIMER OPERATION Three timer modes are available: (Setting of up to 168 hours is enabled) Off timer : The unit stops when the set time is reached Repeat Off timer : The unit stops daily when the set time is reached On timer : The unit starts when the set time is reached Set 1 Push button The timer mode changes with every push of the button Off Off On (Off timer) (Repeat Off timer) (On timer) No display and timer display flashes 2 Push to select set time With every push of button, the set time increases by 05 hr (30 minutes) When setting a time more than 24 hours for timer operation, timer can be set in increments of 1 hr The maximum set time is 168hr (7 days) The remote control displays the set time with time (between 05 and 235 hours) (* 1 ) or number of days and time (24 hours or more) (* 2 ) as shown below With every push of button, the set time decreases by 05 hr (30 minutes) ( hours) or 1 hr ( hours) Example of remote control display 235 hours (* 1 ) 3 Push button icon disappears and time display goes on, and or icon flashes (When On timer is activated, time and On timer are icons and other icons disappear) 4 Cancel timer operation Push button Timer icon disappears NOTE When the operation stops after the timer reached the preset time, the Repeat Off timer resumes the operation by pushing button and stops the operation after the time of the timer has reached the set time When you push while the Off timer function of the air conditioner is active, the indication of the timer function disappears and then appears again after about 5 seconds This is due to normal processing of the remote controller 34 hours (* 2 ) Number of days Time shows 1 day (24 hours) shows 10 hours (Total 34 hours) 13-EN 13 Concealed Duct Hh Static Pressure Owner s Manual 6 POWER SAVING MODE The power saving mode saves energy by limiting the maximum current which will effect heating or cooling capacity that the unit can generate Push button during operation The air conditioner enters power saving mode appears on the display Power saving mode will stay in effect until it is cancelled To cancel the power saving mode, push button again disappears NOTE When other electric appliances are used at the same time, to avoid trgering the circuit breaker, power saving mode is recommended Of course you can use power saving mode to save energy as well Power saving mode consumes less energy, but may not heat/cool the room as much as normal mode (The maximum current is limited to approximately 75% (factory default) of the normal mode) To adjust the power-save settings, see Power saving mode in ADVANCED SETTINGS Even when operation start/stop, operation mode change, or power reset is performed during the power saving mode, the power saving mode is retained until the next operation EN EN Concealed Duct Hh Static Pressure Owner s Manual 7 ADVANCED SETTINGS Power saving mode Push button for at least four seconds when the air conditioner is not working, symbol, and numbers flash 2 Push (left side of the button) to select an indoor unit to be set Each time you push the button, UNIT No change as follows: UNIT No 1-1 UNIT No 1-2 UNIT No UNIT No 1-3 The fan of the selected unit runs 3 Push TIME buttons, to adjust the power saving mode setting Each push of the button changes the power level by 1% within the range from 100% to 50% The factory default is 75% Setting of power level in power saving mode 4 Push button 5 Push button to complete the setting 15-EN 15 Concealed Duct Hh Static Pressure Owner s Manual 8 ENERGY SAVING RECOMMENDATIONS Select a comfortable set point and minimize adjusting it Clean the filter when ever the filter display is illuminated on remote controller Keep doors and windows closed and open them only when necessary Use drapes, curtains, or shades to keep direct sun lht from heating the room on very hot days Do not obstruct the return air grille Adjust the air flow direction for even air distribution in the room Checks before operating Check whether the earth wires are properly connected Check whether the air filters are installed Turn on the leakage breaker at least 12 hours before operating Clean, please Protective device The protective device stops operation when the air conditioner is overloaded When the protective device is activated, the current operation stops and the operation lamp and on the remote controller flash Please close When the protective device is activated When the protective device has been activated and stopped operation, turn off the leakage breaker immediately, and ask the installer to find the cause If the air conditioner is operated without fixing the problem, the air conditioner may malfunction Check whether the air filters are installed If the air filters are not installed, the air heat exchanger may be clogged with dust, which may result in water leakage EN For cooling When the air inlet and/or outlet of the outdoor unit are blocked When the air outlet of the outdoor unit is continuously exposed to strong wind For heating When the air filters are clogged with too much dust or dirt When the suction port and/or discharge port of the indoor unit are blocked Do not turn off the leakage breaker Do not turn off the leakage breaker during a test run of the air conditioner Use the ON/OFF button on the air conditioner instead to control the power EN Concealed Duct Hh Static Pressure Owner s Manual 9 MAINTENANCE WARNING Cleaning the air filter and other parts of the air filter involves dangerous work in hh places, so be sure to have a qualified installer or qualified service person to do it Do not attempt it by yourself Cleaning air filters Clogged air filters will reduce the cooling and heating performance (1) If is displayed on the remote controller, clean the air filters (2) When the cleaning of air filters has been completed, push button disappears (1) (2) CAUTION Cleaning remote controller Use a dry cloth to wipe the remote controller Never use a damp cloth on the remote controller Do not use a chemiy-treated duster for wiping or leave such materials on the unit for long It may damage or fade the surface of the unit Do not use benzine, thinner, polishing powder, or similar solvents for cleaning These may cause the plastic surface to crack or deform Periodic check Long-period use of the air conditioner may cause deterioration or failure of parts due to heat, humidity, dust, and operating conditions, or may cause poor drainage of dehumidified water Preparing for long Shut Down Period (1) Clean the filters and reposition them in unit (2) Operate the unit in fan mode for 3 or 4 hours to dry all internal parts (3) Turn the unit off and disconnect the main power supply (4) Before unit is turned on again, make sure the circuit breaker has been turned on for at least 12 hours Check points before operation (1) Check that the air filters are installed (2) Check that the air outlet or inlet is not blocked (3) Turn on the main power switch or the circuit breaker for the main power supply to the air conditioner NOTE For environmental conservation, it is strongly recommended that the indoor and outdoor units of the air conditioner in use be cleaned and maintained regularly to ensure efficient operation of the air conditioner When the air conditioner is operated for a long time, periodic maintenance (once a year) is recommended Furthermore, regularly check the outdoor unit for rust and scratches, and remove them or apply rustproof treatment, if necessary As a general rule, when an indoor unit is operated for 8 hours or more daily, clean the indoor unit and outdoor unit at least once every 3 months Ask a professional for this cleaning/maintenance work Such maintenance can extend the life of the product though it involves the owner s expense Failure to clean the indoor and outdoor units regularly will result in poor performance, freezing, water leakage, and even compressor failure 17-EN 17 Concealed Duct Hh Static Pressure Owner s Manual Maintenance List Part Unit Check (visual/auditory) Maintenance Heat exchanger Indoor/outdoor Dust/dirt clogging, scratches Wash the heat exchanger when it is clogged Fan motor Sound Take appropriate measures when abnormal Indoor/outdoor sound is generated Filter Indoor Dust/dirt, breakage Wash the filter with water when it is contaminated Replace it when it is damaged Fan Air inlet/outlet grilles Drain pan Ornamental panel, louvers Exterior Indoor Indoor/outdoor Indoor Indoor Outdoor Vibration, balance Dust/dirt, appearance Dust/dirt, scratches Dust/dirt clogging, drain contamination Dust/dirt, scratches Rust, peeling of insulator Peeling/lift of coat Replace the fan when vibration or balance is terrible Brush or wash the fan when it is contaminated Fix or replace them when they are deformed or damaged Clean the drain pan and check the downward slope for smooth drainage Wash them when they are contaminated or apply repair coating Apply repair coating EN EN Concealed Duct Hh Static Pressure Owner s Manual 10AIR CONDITIONER OPERATIONS AND PERFORMANCE 3 minutes protection function 3-minutes protection function prevents the air conditioner from starting for initial 3 minutes after the main power switch/circuit breaker is turned on for re-starting the air conditioner Power failure Power failure during operation will stop the unit completely To restart the operation, push the ON/OFF button on the remote controller Lhtning or a wireless car telephone operating nearby may cause the unit to malfunction Turn off the main power switch or circuit breaker and then turn them on again Push the ON/OFF button on the remote controller to restart Heating characteristics Preheating operation The air conditioner will not deliver warm air immediately after it is turned on Warm air will start to flow out after approximately 5 minutes when the indoor heat exchanger warmed up Warm air control (In heating operation) When the room temperature has reached the set temperature while the outdoor unit is stopping, the indoor unit discharges wind with a very small air volume Defrosting operation If the outdoor unit is frosted during the heating operation, defrosting starts automatiy (for approximately 2 to 10 minutes) to maintain the heating capacity The fans in both indoor and outdoor units will stop during the defrosting operation During the defrosting operation, the defrosted water will be drained from the bottom plate of the outdoor unit Heating capacity In the heating operation, the heat is absorbed from the outside and brought into the room This way of heating is ed heat pump system When the outside temperature is too low, it is recommended to use another heating apparatus in combination with the air conditioner Attention to snowfall and freeze on the outdoor unit In snowy areas, the air inlet and air outlet of the outdoor unit are often covered with snow or frozen up If snow or freeze on the outdoor unit is left as it is, it may cause machine failure or poor warming In cold areas, pay attention to the drain hose so that it perfectly drains water without water remaining inside for freeze prevention If water freezes in the drain hose or inside the outdoor unit, it may cause machine failure or poor warming Air conditioner operating conditions For proper performance, operate the air conditioner under the following temperature conditions: Cooling operation Heating operation Outdoor temperature : 15 C to 46 C Room temperature : 21 C to 32 C (Dry bulb temp), 15 C to 24 C (Wet bulb temp) [CAUTION] Outdoor temperature Room temperature Room relative humidity less than 80 % If the air conditioner operates in excess of this fure, the surface of the air conditioner may cause dewing : 20 C to 15 C (Wet bulb temp) : 15 C to 28 C (Dry bulb temp) If air conditioner is used outside of the above conditions, safety protection may work 19-EN 19 Concealed Duct Hh Static Pressure Owner s Manual 11INSTALLATION Do not install the air conditioner in the following places Do not install the air conditioner in any place within 1 m from a TV, stereo, or radio set If the unit is installed in such place, noise transmitted from the air conditioner affects the operation of these appliances Do not install the air conditioner near a hh frequency appliance (sewing machine or massager for business use, etc), otherwise the air conditioner may malfunction Do not install the air conditioner in a humid or oily place, or in a place where steam, soot, or corrosive gas is generated Do not install the air conditioner in a salty place such as seaside area Do not install the air conditioner in a place where a great deal of machine oil is used Do not install the air conditioner in a place where it is usually exposed to strong wind such as in seaside area Do not install the air conditioner in a place where sulfureous gas generated such as in a spa Do not install the air conditioner in a vessel or mobile crane Do not install the air conditioner in an acidic or alkaline atmosphere (in a hot-spring area or near a chemicals factory, or in a place subject to combustion emissions) Corrosion may be generated on the aluminum fin and copper pipe of the heat exchanger Do not install the air conditioner near an obstacle (air vent, lhting equipment, etc) that disturbs discharge air (Turbulent airflow may reduce the performance or disable devices) Do not use the air conditioner for special purposes such as preserving food, precision instruments, or art objects, or where breeding animals or growing plants are kept (This may degrade the quality of preserved materials) Do not install the air conditioner over an object that must not get wet (Condensation may drop from the indoor unit at a humidity of 80% or more or when the drain port is clogged) Do not install the air conditioner in a place where an organic solvent is used Do not install the air conditioner near a door or window subject to humid outside air Condensation may form on the air conditioner Do not install the air conditioner in a place where special spray is used frequently EN Be careful with noise or vibrations Do not install the air conditioner in a place where noise by outdoor unit or hot air from its air outlet annoys your nehbors Install the air conditioner on a solid and stable foundation so that it prevents transmission of resonating, operation noise and vibration If one indoor unit is operating, some sound may be audible from other indoor units that are not operating EN Concealed Duct Hh Static Pressure Owner s Manual 12TROUBLESHOOTING CAUTION If any of the following conditions occur, turn off the main power supply switch and immediately contact the dealer : Switch operation does not work properly The main power fuse often blows out, or the circuit breaker is often activated A foren matter or water fall inside the air conditioner When the air conditioner does not operate even after the cause of the protective device activation has been removed (The operation lamp and on the remote controller are flashing) Any other unusual conditions are observed Before you ask for servicing or repairs, check the following points Recheck Inoperative The main power switch is turned off The circuit breaker is activated to cut off power supply The main power fuse has blown out Does not cool well or heat well The air inlet and/or outlet of the outdoor unit is blocked Doors or windows are opened The set temperature is too hh (In cooling) or low (In heating) These are not failures Indoor unit or outdoor unit makes a strange noise When the temperature suddenly changes, the indoor or outdoor unit occasionally makes a strange noise because of expansion/ contraction of parts or change of refrerant flow Air leaking noise is heard occasionally It is generated by the solenoid valve when it is actuated A clattering sound is heard when the power is turned on It is generated by the outdoor unit during preparation for operation The room air is smelly or a bad odor comes from the air conditioner Smells impregnated in the walls carpets, furniture, clothing, or furs, come out Outdoor unit is frosted in heating operation Water drains from outdoor unit The outdoor unit is sometimes frosted in heating operation In that case, the unit automatiy performs defrosting (for 2 to 10 minutes) for increasing the heating efficiency In defrosting operation, both the indoor and outdoor units stop air flow Hiss sound is heard when flow of the refrerant is changed for defrosting Resultant water of automatic defrosting in heating operation drains from outdoor unit A white mist of chilled air or water is generated from the outdoor unit When the indoor unit in cooling operation or the outdoor unit in defrosting operation occasionally steams Check these items If any of these problems still remains, stop the operation, turn off the leakage breaker, and then notifies the dealer of the serial number and details of the error Never repair any part by yourself as it is dangerous When and a combination of,,,, or and a number are displayed on the remote controller, also inform the dealer of the display content 21-EN 21 Concealed Duct Hh Static Pressure Owner s Manual 13SPECIFICATIONS Model Sound power level (db) Cooling Heating Weht (Kg) RAV-SM2242DT-E RAV-SM2802DT-E Declaration of Conformity Manufacturer: Authorized Representative/ TCF holder: Toshiba Carrier Corporation 336 Tadehara, Fuji-shi, Shizuoka-ken JAPAN Nick Ball Toshiba EMEA Engineering Director Toshiba Carrier UK Porsham Close, Belliver Industrial Estate, PLYMOUTH, Devon, PL6 7DB United Kingdom Hereby declares that the machinery described below: EN Generic Denomination: Model/type: Commercial name: Air Conditioner RAV-SM2242DT-E, RAV-SM2802DT-E, RAV-SM2242DT-TR, RAV-SM2802DT-TR Dital Inverter Series Air Conditioner Complies with the provisions of the Machinery Directive (Directive 2006/42/EC) and the regulations transposing into national law Complies with the provisions of the following harmonized standard: EN 378-2: 2008 NOTE This declaration becomes invalid if cal or operational modifications are introduced without the manufacturer s consent EN Pression statique élevée du conduit dissimulé Manuel du propriétaire Translated instruction CHOIX D UN NOUVEAU RÉFRÉRANT Ce climatiseur utilise un fluide frorène écologique, le R410A Cet appareil n est pas conçu pour une utilisation par une personne (y compris des enfants) à mobilité réduite, ou déficiente mentalement ou manquant d expérience et de connaissances, à moins qu elle ait reçu des instructions ou une supervision concernant l utilisation de l appareil par une personne responsable de leur sécurité Table des matières 1 MESURES DE SÉCURITÉ 26 2 NOM DES PIECES 29 3 TELECOMMANDE AVEC FIL 30 4 UTILISATION CORRECTE 33 5 FONCTIONNEMENT DE LA MINUTERIE 35 6 MODE D ECONOMIE D ENERGIE 36 7 PARAMÈTRES AVANCÉS 37 8 RECOMMANDATIONS D ECONOMIE D ENERGIE 38 9 ENTRETIEN FONCTIONNEMENT ET PERFORMANCE DU CLIMATISEUR INSTALLATION DIAGNOSTIC DES PANNES SPECIFICATIONS 44 1-FR 23 Pression statique élevée du conduit dissimulé Manuel du propriétaire Merci d avoir acheté ce climatiseur Toshiba Veuillez lire attentivement ces instructions qui contiennent des informations importantes qui sont conformes à la directive «Machines» (Directive 2006/42/EC), et assurez-vous de bien les comprendre Certains détails de ces instructions sont différentes de celles du Manuel du propriétaire fourni avec votre produit, toutefois les instructions fournies ici sont prioritaires Après lecture de ces instructions, veuillez les garder en lieu sûr avec le Manuel du propriétaire et le Manuel d installation fournis avec votre produit Dénomination générique : climatiseur Définition d installateur qualifié ou de personne d entretien qualifiée Le climatiseur doit être installé, entretenu, réparé et enlevé par un installateur qualifié ou une personne d entretien qualifiée Lorsqu une de ces tâches doit être effectuée, demandez à un installateur qualifié ou à une personne d entretien qualifiée de les réaliser pour vous Un installateur qualifié ou une personne d entretien qualifiée est un agent qui possède les qualifications et les connaissances décrites dans le tableau ci-dessous Agent Installateur qualifié Personne d entretien qualifiée Qualifications et connaissances que l agent doit posséder L installateur qualifié est une personne qui installe, entretient, déplace et enlève les climatiseurs fabriqués par Toshiba Carrier Corporation Il ou elle a été formé pour installer, entretenir, déplacer et enlever les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes concernant de telles opérations par une ou des personnes qui ont été formés et a, par conséquent, acquis toutes les connaissances associées à ces opérations L installateur qualifié qui est autorisé à effectuer un travail électrique compris dans l installation, le déplacement et l enlèvement possède les qualifications nécessaires à ce travail électrique conformément aux réglementations et à la législation locales, et il ou elle est une personne qui a été formée pour les problèmes relatifs au travail électrique sur les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes dans de tels domaines par une ou des personnes qui ont été formées et possèdent, par conséquent, les connaissances relatives à ce travail L installateur qualifié qui est autorisé à manipuler du fluide frorène et à réaliser un travail de raccordement compris dans l installation, le déplacement et l enlèvement possède les qualifications nécessaires à cette manipulation de fluide frorène et de ce travail de raccordement conformément aux réglementations et à la législation locales, et il ou elle est une personne qui a été formée pour les problèmes relatifs à la manipulation de fluide frorène et de travail de raccordement sur les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes dans de tels domaines par une ou des personnes qui ont été formées et possèdent, par conséquent, les connaissances relatives à ce travail L installateur qualifié qui est autorisé à travailler en hauteur a été formé aux domaines relatifs au travail en hauteur avec les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes dans de tels domaines par une ou des personnes qui ont été formées et possèdent, par conséquent, toutes les connaissances requises pour ce travail La personne d entretien qualifiée est une personne qui installe, répare, entretient, déplace et enlève les climatiseurs fabriqués par Toshiba Carrier Corporation Il ou elle a été formé pour installer, réparer, entretenir, déplacer et enlever les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes pour de telles opérations par une ou des personnes qui ont été formées et a, par conséquent, acquis toutes les connaissances associées à ces opérations La personne d entretien qualifiée qui est autorisée à effectuer un travail électrique compris dans l installation, la réparation, le déplacement et l enlèvement possède les qualifications nécessaires à ce travail électrique conformément aux réglementations et à la législation locales, et il ou elle est une personne qui a été formée pour les problèmes relatifs au travail électrique sur les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes dans de tels domaines par une ou des personnes qui ont été formées et possèdent, par conséquent, les connaissances relatives à ce travail La personne d entretien qualifiée qui est autorisée à manipuler du fluide frorène et à réaliser un travail de raccordement compris dans l installation, la réparation, le déplacement et l enlèvement possède les qualifications nécessaires à cette manipulation de fluide frorène et de ce travail de raccordement conformément aux réglementations et à la législation locales, et il ou elle est une personne qui a été formée pour les problèmes relatifs à la manipulation de fluide frorène et de travail de raccordement sur les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes dans de tels domaines par une ou des personnes qui ont été formées et possèdent, par conséquent, les connaissances relatives à ce travail La personne d entretien qualifiée qui est autorisée à travailler en hauteur a été formé aux domaines relatifs au travail en hauteur avec les climatiseurs fabriqués par Toshiba Carrier Corporation ou, alternativement, il ou elle a reçu des consnes dans de tels domaines par un ou des personnes qui ont été formées et possèdent, par conséquent, toutes les connaissances requises pour ce travail FR 24 2-FR Pression statique élevée du conduit dissimulé Manuel du propriétaire Indications d avertissement relatives au climatiseur Indication d avertissement Description WARNING ELECTRICAL SHOCK HAZARD Disconnect all remote electric power supplies before servicing AVERTISSEMENT DANGER DE CHOC ELECTRIQUE Débranchez toutes les sources d alimentation en électricité à distance avant l entretien WARNING Moving parts Do not operate unit with grille removed Stop the unit before the servicing AVERTISSEMENT Pièces mobiles Ne faites pas fonctionner l unité en l absence de grille Arrêtez l unité avant l entretien CAUTION Hh temperature parts You mht get burned when removing this panel ATTENTION Pièces haute température Vous risquez de vous brûler lors de la dépose de ce panneau CAUTION Do not touch the aluminum fins of the unit Doing so may result in injury ATTENTION Ne touchez pas les ailettes en aluminium de l unité Dans le cas contraire, vous pourriez vous blesser CAUTION BURST HAZARD Open the service valves before the operation, otherwise there mht be the burst ATTENTION DANGER D EXPLOSION Ouvrez les clapets d alimentation avant l utilisation, dans le cas contraire, une explosion pourrait survenir 3-FR 25 Brix Ratio Check Instructions for Cold Fusion and Flavor Overload Units INSTALLATION INSTRUCTIONS Brix Ratio Check Instructions For Coldfusion, Flavorfusion and Flavor Overload Units Kit P/N 629096865 SAFETY Más detalles Agustiniano Ciudad Salitre School Computer Science Support Guide - 2015 Second grade First term UNIDAD TEMATICA: INTERFAZ DE WINDOWS LOGRO: Reconoce la interfaz de Windows para ubicar y acceder a los programas, Más detalles DIAMOND Gear Company, . 5 Más detalles FUSIBLES CILÍNDRICOS 10x85 PARA INSTALACIONES FOTOVOLTAICAS CYLINDRICAL FUSE-LINKS 10x85 FOR PHOTOVOLTAIC INSTALLATIONS gpv 1500- FICHA TÉCNICA / CAL DATA SHEET DF, S. Silici, 67-69 08940 CORNELLA Más detalles OWNER S MANUAL RELAX ECO RELAX MULTI RELAX ENGLISH ESPAÑOL FRANÇAIS DEUTSCH NEDERLANDS PORTUGUÊS ENGLISH CONTENTS SAFETY PRECAUTIONS... BATERÍA El dispositivo cuenta con Más detalles WL1003 NEW AUTOMÁTICO Acaba de adquirir un equipo de conmutación de euroconectores y le damos las gracias por su elección. Utilice Más detalles 20-1/4 514 mm 67-3/4 1721 mm 93-3/4 2382 mm NOTE/ NOTE/ NOTA 1) THIS WALLBED IS TO BE USED IN HOMES WITH STANDARD CONSTRUCTION, THE BUTTERFLY TOGGLES ARE TO BE USED IN DRY- WALL THAT IS AT LEAST 1/2 DEEP.

Diagnostico inverter - El Aire Acondicionado

¡Solícite el manual que busca haciendo click en la página 'Solicitar un manual' y nosotros se lo mandaremos!

CATALOGO GENERAL <strong>PANASONIC</strong> 2016- PanasonicProClub

PANASONIC CSS12JKUW - SPLIT A/C INDOOR OPERATING.

An ERIKS Company Installation, Maintenance, & Operation Manual 2013 INSTRUCTIONS This is an instructional manual which provides general installation, operation, and maintenance Más detalles GUÍA DE USUARIO PC-331117 Bienvenidos al mundo Perfect Choice Antes de comenzar a usar el producto es importante que leas esta guía. Inserta el transmisor en el conector para encendedor de Más detalles Video Server Quick Installation Guide English, Español 2 Video Server NOTES Quick Installation Guide 3 Video Server Quick Installation Guide To get your Video Server up and running on an Ethernet network, Más detalles SIVACON Armario de distribución de energía homologado S4/S8 Transporte y almacenamiento de armarios eléctricos/ Type-tested Power Distribution Board S4 / S8 Transport and Storage of Switchboards S4 / S8 Más detalles FCC Information : This device complies with Part 15 of the FCC Rules. Para una utilización óptima de este aparato, le recomendamos que lea este manual Más detalles Guía del usuario Funda con batería CP12 Contenido Introducción...3 La carga más sencilla...3 Especificaciones...3 Uso de la funda con batería...4 Carga del teléfono...4 Información legal...6 2 Introducción Más detalles KAISSA Manual Rápido De Usuario Rev 1.0 Ante todo gracias por adquirir el innovador reloj de ajedrez KAISSA, diseñado bajo la filosofía del Diseño Para Todos.

Manual técnico - Kaysun

¿El manual de su Panasonic Aires acondicionados no está disponible?


Manual de instrucciones aire acondicionado panasonic r410a:

Rating: 100 / 100

Overall: 96 Rates